Troubleshooting
Locating a ground fault on a resistance-grounded 480 V system
Short answer
Phase-to-ground readings of 420, 380 and 77 V with all phase-to-phase voltages at 480 V mean the neutral has shifted toward P3: a first ground fault on P3, its current limited by the neutral grounding resistor. Locate it by resistor voltage and current, timing against process events, then feeder-by-feeder isolation, because a second fault on another phase becomes a phase-to-phase fault through ground.
On this page
- What the 420, 380 and 77 V readings mean
- Record these numbers before you isolate anything
- Worked example: the 1000 kVA secondary reading 420/380/77 V to ground
- Locating the fault, step by step
- Pulsing circuits, ground lights and clamp meters
- Decisions by what you see
- The standards behind the design
- Questions asked
The readings are diagnostic, not a transformer problem. With every phase-to-phase voltage at 480 V and phase-to-ground voltages of 420 V, 380 V and 77 V, the neutral point has shifted toward P3: this is a first ground fault on P3, with its current held to a few amperes by the neutral grounding resistor. The load currents of 80, 80 and 85 A on a 1000 kVA transformer are normal and cannot show it. Locate the fault by watching the resistor branch, correlating alarm times with process events, and opening feeders one at a time — and treat it as urgent, because a second fault on another phase becomes a phase-to-phase fault through ground.
What the 420, 380 and 77 V readings mean #
A delta-wye transformer serving a three-wire MCC still has a wye neutral point: the neutral grounding resistor ties that point, at the transformer's XO bushing, to the ground bus, and that resistor is the system's ground reference. Healthy, each phase reads about 277 V to ground, which is the line-to-line voltage ÷ √3. When one phase develops a leakage path to ground, the neutral is pulled toward that phase: the faulted phase's reading falls and the two healthy phases rise toward line-to-line voltage. On a bolted fault the faulted phase sits near 0 V and the healthy phases near phase-to-phase voltage; 77 V on P3 with 420 V and 380 V on P1 and P2 is the same shift partway — an insulation path with resistance, or an arcing connection, not a bolted weld.
The lowest phase-to-ground reading names the faulted phase: P3. It does not name the location. The path can be in the secondary winding, the cable or bus to the MCC, any feeder, a motor stator, a heater circuit, or a remote 480 V solenoid. Because the neutral is grounded through resistance, fault current stays small, burning at the fault is limited, and the intermittent-fault overvoltages that plague ungrounded systems are suppressed — the reasons the design exists. The price is that the system keeps running with a fault on it until a second fault on another phase turns the pair into a phase-to-phase fault through ground, possibly opening two overcurrent devices at once.
Record these numbers before you isolate anything #
- All three phase-to-phase and all three phase-to-ground voltages at the MCC, and the same six at the transformer secondary, taken in the same operating state with a true-rms meter rated for the measurement category at that location.
- Voltage across the neutral grounding resistor and current in the resistor branch, with the instrument noted.
- The three phase currents — they rule the load in or out, nothing more.
- Ground-alarm start and stop times, and what the process was doing at those moments.
- The resistor nameplate: resistance, voltage rating, current rating and duty (continuous or short-time).
- The one-line diagram as actually built, checked against the conductors in the raceways.
Worked example: the 1000 kVA secondary reading 420/380/77 V to ground #
Inputs:
- Field measurements at the MCC: 480 V phase-to-phase on all three pairs; P1 420 V, P2 380 V, P3 77 V to ground; line currents 80 A, 80 A, 85 A.
- Nameplate: 1000 kVA, 13.8 kV high voltage to this low-voltage secondary, three-phase delta-wye, resistance-grounded secondary, three wires to the MCC. Full-load secondary current is 1000 ÷ (3 × 0.277) ≈ 1203 A.
- Assumed for the arithmetic, because the resistor value was not recorded: a 27.7 Ω neutral grounding resistor, a 10 A at 277 V unit. Substitute your nameplate value.
Rules in words: nominal phase-to-neutral voltage is line-to-line voltage divided by √3; apparent load is three times phase voltage times average line current; neutral displacement is nominal phase voltage minus the faulted phase's reading; resistor current is displacement ÷ resistance, and resistor heating is displacement² ÷ resistance — all before system capacitance and fault impedance, so treat them as estimates to check against the nameplate and the governing code.
Arithmetic:
- 480 ÷ 1.732 = 277 V, the healthy phase-to-ground value.
- Average current (80 + 80 + 85) ÷ 3 = 81.7 A; load = 3 × 277 × 81.7 ≈ 68 kVA, which is 6.8% of 1000 kVA. The 4% spread between phases is ordinary load unbalance. No overload, and nothing in these currents points at the fault.
- Neutral displacement ≈ 277 − 77 = 200 V.
- Resistor current ≈ 200 ÷ 27.7 = 7.2 A, flowing continuously through the fault and back through the grounding system.
- Resistor heating ≈ 200² ÷ 27.7 = 40,000 ÷ 27.7 ≈ 1440 W.
- If the fault goes bolted: 277 ÷ 27.7 = 10.0 A and 277² ÷ 27.7 ≈ 2770 W.
- Fault-path resistance ≈ 77 ÷ 7.2 ≈ 11 Ω (rough, assuming a resistive path) — why P3 sits at 77 V instead of 0 V.
- Consistency check: a 200 V displacement puts both healthy phases near 415 V by phasor arithmetic; the measured 420/380 V pair brackets that, the spread owed to load unbalance.
Result: a first ground fault on P3, about 7 A of continuous ground current through roughly 11 Ω of fault path. Decision: the faulted phase is P3 — any phase pulled well below 277 V while the other two rise is the faulted one, and 77 V is unambiguous. Keep the bus energized only while the resistor nameplate covers 1440 W continuous and someone is actively hunting; a short-time rating (10 s or 1 min) means taking feeders down instead of searching live. Start isolation on feeders serving cycling equipment, guided by the alarm log; the feeder whose opening lifts P3 back above 250 V, within about 10% of the healthy 277 V, carries the fault.
Locating the fault, step by step #
This is an energized power system with a known ground fault on it. The single-fault continuity of a resistance-grounded system is a grace period for locating and clearing the fault, not a standing condition to run on. Follow the site electrical safety program and NFPA 70E, 2024 edition, with qualified persons only: before any terminal box, motor connection box or drive cover opens, the circuit behind it is de-energized, locked out and tested for absence of voltage. Opening feeders is switching, done under an approved plan while someone watches the grounding branch.
- Verify the configuration against reality: transformer nameplate, one-line diagram, the resistor between XO and the ground bus, feeder labels versus the conductors actually installed.
- Repeat the six voltage readings at the transformer secondary and compare with the MCC set in the same operating state. A displacement present at both is a system condition and confirms your measurement reference.
- Read the grounding branch: voltage across the resistor and current in it. Check V ÷ I against the nameplate resistance as a sanity check on the instruments.
- Put timing to work. Log alarm start and stop against motor starts, solenoid operations, heater cycles and washdown. An indication that appears when a starter closes lives downstream of that starter. Ground lights — one indicating lamp per phase — make the shift visible from the floor while equipment cycles.
- Open one feeder at a time under the switching plan, watching the resistor voltage or all three phase-to-ground readings. When the shift collapses and the faulted phase climbs back toward 277 V, that feeder holds the fault; keep it isolated and repeat at its branches.
- With the faulted branch identified: de-energize, lock out, verify absence of voltage, then insulation-test the circuit — cable, motor windings, heaters, solenoids — reading phase-to-ground against phase-to-phase results as motor insulation testing, phase-to-phase versus phase-to-ground explains. Repair, re-energize, and confirm all three phase-to-ground readings sit near 277 V again.
Pulsing circuits, ground lights and clamp meters #
A pulsing accessory periodically switches a resistor in parallel with the main grounding resistor, stepping the ground-fault current up by a few amperes on a cycle so a clamp meter can follow the pulse along the faulted feeder. Field results split on it. Crews that get value from pulsing clamp all three phase conductors of a suspect feeder together with a large-jaw, low-range clamp and read the pulse as net current; crews that do not report that the returning current divides among too many bonding and grounding paths to trace, the same division behind diagnosing current on equipment grounding conductors. On those systems, a widely visible set of ground lights watched while equipment cycles, plus an alarm log with time stamps, finds the machine faster. Whichever method you run, log the alarm: the start time against the process is the strongest locating evidence you will get.
Decisions by what you see #
| Observation | Decision |
|---|---|
| All phase-to-phase voltages at nominal; one phase-to-ground low, two high (420/380/77 V here) | First ground fault on the low phase, P3. Begin location now; run only with detection alarmed and the log kept. |
| Faulted phase near 0 V, healthy phases near line-to-line voltage | The same fault, now bolted, at full resistor current. Same phase, faster isolation. |
| Phase-to-ground readings change as equipment cycles | Fault is downstream of a starter or contactor feeding that equipment; open that branch first. |
| Readings wander with no matching change in resistor voltage or current | Check the grounding connection, measurement reference and meter before blaming a feeder; trace the grounding path against the one-line. |
| The shift clears when one feeder opens | That feeder holds the fault. Isolate it, de-energize, verify, then test its branches. |
| No ground-fault detection installed | Add it before the next fault: the design depends on knowing the first fault exists. |
The standards behind the design #
NFPA 70, the National Electrical Code, 2023 edition, permits high-impedance grounded neutral systems on three-phase systems of this voltage class in 250.36, conditioned on qualified-person maintenance and supervision, installed ground-fault detection, and no line-to-neutral loads — your three-wire, no-neutral installation matches that last condition. IEEE 142, the 2007 edition of the IEEE recommended practice for grounding industrial and commercial power systems, covers resistance-grounded design, including choosing the grounding resistance against the system's charging current so the neutral shift is well defined and arcing overvoltages are damped. Confirm how these apply with the authority having jurisdiction and the equipment documentation.
Questions asked
Why do the phase currents stay at 80, 80 and 85 A with a ground fault on the system?
The grounding resistor, not the transformer's 1000 kVA, sets ground-fault current. A 27.7 Ω unit limits even a bolted fault to 277 ÷ 27.7 = 10 A, and the 7 A or so flowing in this case returns through the grounding branch and the bonded steel, not through the phase conductors in any way a feeder ammeter resolves. The resistor branch, its voltage and its current, is the meter that sees this fault.
How long can we keep running on one ground fault?
Only as long as the neutral grounding resistor is rated continuous for the fault heating, about 1440 W at this 200 V displacement and 2770 W if the fault goes bolted, and only while the ground alarm is being acted on. Read the nameplate duty: a short-time-rated resistor means you stop searching energized and shut the faulted feeder down. Either way the clock runs toward a second fault on another phase, which is a phase-to-phase fault through ground.
What does a pulsing circuit change, numerically?
It steps the fault current so a clamp meter can follow it. With a 27.7 Ω main resistor, a 100 Ω pulsing resistor switched in parallel gives (27.7 × 100) ÷ 127.7 ≈ 21.7 Ω, so fault current rises from 277 ÷ 27.7 = 10.0 A to 277 ÷ 21.7 ≈ 12.8 A. That roughly 3 A step, switched on and off, is what you trace along the faulted feeder. It is an engineered accessory matched to the resistor and contactor ratings, not a field improvisation.
Where on P3 can the fault turn out to be, and can it move?
Anywhere the P3 conductor reaches: the transformer secondary winding, the cable or bus to the MCC, a feeder, a motor winding, a heater circuit, control wiring or a remote solenoid. It can also be intermittent, showing only while a particular starter is closed, and the readings can shift when equipment cycles. That movement, timed against process events, is locating evidence, not a contradiction.
Does a resistance-grounded system need ground-fault detection?
Yes. NFPA 70, the National Electrical Code, 2023 edition, conditions high-impedance grounded neutral systems in 250.36 on installed ground-fault detection, qualified-person maintenance and supervision, and no line-to-neutral loads. Detection is also what makes the design workable: an alarmed, logged indication with a time stamp is what ties the fault to the machine that was starting when it began. Confirm the requirement with your authority having jurisdiction and the equipment documentation.