Current IntelPower LibraryShop main store

Selection guide

Stopping breaker trips on 25 kVA transformer inrush

Protection: breakers, fuses and SCCR Published 9 min read

Short answer

Set a breaker with a programmable electronic trip unit so its instantaneous pickup sits above the transformer's inrush peak, and the energization trips stop with no added power hardware: for a 25 kVA, 400 V primary that is 36 A rated current and up to about 540 A first-cycle inrush. A motor soft starter is the fallback only if its documentation permits a transformer magnetizing load; resistor pre-insertion is the engineered option when the supply itself cannot tolerate the dip.

On this page
  1. The current that is tripping the breakers
  2. Why ordinary breakers open, and what a trip unit changes
  3. Worked setting for a 25 kVA, 400 V primary
  4. The four fixes compared
  5. The soft starter: documentation decides
  6. Resistor pre-insertion: when the dip is the problem
  7. Proving the fix on site
  8. Questions asked

Stop the trips with the protection, not with added power hardware: a molded-case breaker with a programmable electronic trip unit, its instantaneous pickup set above the transformer's inrush peak, holds through every energization and still clears faults. For a 25 kVA, 400 V three-phase primary that is 36.1 A of rated current and a worst-case first-cycle inrush of fifteen times that, met with a 63 A frame, a 50 A long-time setting and a 630 A instantaneous pickup. A motor soft starter earns its place only when its documentation permits a transformer magnetizing load, and resistor pre-insertion only when the supply dip itself, not the trip, is what hurts. This article works the numbers and picks between the four fixes.

The current that is tripping the breakers #

Rated primary current from the nameplate, treating 400 V as the primary line-to-line voltage:

I = S / (√3 × V_LL) = 25,000 VA / (1.732 × 400 V) = 25,000 / 692.8 = 36.1 A

Energizing the transformer draws magnetizing inrush and nothing else; the connected load does not matter yet. The documented envelope for this transient is 10 to 15 times rated current for 0.1 to 0.5 s, decaying as the core flux settles:

  • Low end: 10 × 36.1 A = 361 A
  • Worst case: 15 × 36.1 A = 541.5 A, call it 542 A

Where a given energization lands inside that envelope depends on the point on the voltage wave where the contacts close and on the residual flux left in the core from the last de-energization, which is why the same transformer trips protection on some starts and not others. Before moving any setting, pin the envelope down for the actual unit the way estimating transformer inrush current for protection coordination works it, because every setting below is checked against that number. This calculation is an estimate: confirm the primary voltage and connection against the nameplate and the result against the governing code and the equipment documentation.

Why ordinary breakers open, and what a trip unit changes #

A 50 A miniature breaker of the common curves picks up in this range:

Curve per IEC 60898-1 Instantaneous pickup 50 A device picks up at
B 3–5 × In 150–250 A
C 5–10 × In 250–500 A
D 10–20 × In 500–1000 A

IEC 60898-1 is the product standard covering miniature circuit-breaker ratings and tripping characteristics. A type C device begins to trip anywhere inside the low-end-to-worst-case envelope, a type B cannot survive it, and a type D straddles it, so it rides the mild energizations and trips on the bad ones. An adjustable electronic trip unit makes the outcome deterministic instead of statistical. Molded-case breakers with programmable ETUs, the Siemens 3VL line with its trip units being one example of the class, typically expose six adjustments: continuous current Ir, long-time delay, short-time pickup, short-time delay, instantaneous pickup, and ground fault.

Two things an ETU is not: it does not limit current while it holds the breaker closed, it only decides when to open; and current-limiting on a breaker datasheet means let-through energy while interrupting a fault, which is the breaker opening, exactly what you are trying to avoid. The full inrush peak still flows into the transformer and out of the supply, so the fix is protection placed above it while the supply tolerates the transient. Where the coordination must be documented against the low-voltage overcurrent standards, the split of duties between an electronic trip unit and a protective relay for LV overcurrent coordination decides which device carries the settings. Confirm the trip unit's exact setting ranges against the documentation for the frame you buy.

Worked setting for a 25 kVA, 400 V primary #

Worked example, all inputs stated: 25 kVA three-phase transformer, 400 V primary line-to-line, 36.1 A rated primary current, worst-case inrush taken as fifteen times rated current.

  • Long-time pickup: NFPA 70, the National Electrical Code, 2023 edition, Table 450.3(B), which sizes overcurrent protection for transformers rated 1000 V or less, permits a primary-only circuit breaker at up to 125 % of rated primary current, with the next higher standard rating allowed when 125 % falls between sizes. Here 1.25 × 36.1 A = 45.1 A, so the setting is 50 A; on a 63 A frame that is Ir = 50 A. Where the NEC does not govern, 50 A on a 36 A load is still the right engineering setting. Confirm the rule as locally amended with the authority having jurisdiction.
  • Short-time: pickup at 8 × Ir = 400 A, delay in the longest band the downstream coordination allows, 0.3 s as the example. The envelope puts the decaying inrush below 400 A well inside that time.
  • Instantaneous: 10 × In = 10 × 63 A = 630 A, which sits above the calculated worst-case peak by 630 / 541.5 = 1.16, a 16 % margin.

One check keeps this honest: the pickup must stay well below the minimum fault current the breaker has to clear. Measure the available fault current at the breaker; if a weak supply could not push a bolted fault past 630 A, the supply impedance is the project's real problem, not the settings.

Decision for the common case, where the breaker opens only at energization and other loads shrug off the dip: set the ETU to the numbers above, verify each one against the actual breaker's ranges and time-current curves, and stop there.

The four fixes compared #

Option What it does to the transient Choose it when Verify before committing
Breaker with programmable ETU Nothing; the full inrush flows and protection sits above it The breaker trips only at energization and the supply stands the dip Instantaneous at 630 A against the calculated worst-case peak; Ir = 50 A within the 125 % rule; fault current still detected
Type D breaker or aM fuse, same rating Nothing; the fixed pickup band sits higher, 10–20 × In Replacing a B or C device and no adjustments are wanted The 500–1000 A band on a 50 A unit straddles the worst-case peak; an aM fuse needs a downstream device to clear low-level faults
Soft starter in the primary Ramps the applied voltage, holding the core out of saturation; peak near rated current The model's documentation lists transformer duty, or the ETU route is impractical Rating at or above 36.1 A continuous, bypass behavior, heating across repeated energizations
Resistor pre-insertion Series resistance caps the first cycles, then is bypassed once flux settles The voltage dip itself trips or disturbs other loads on a weak supply Pulse energy per energization, bypass sequencing, failed-bypass protection

The soft starter: documentation decides #

A voltage ramp can work on a transformer for a physical reason: core flux is the time integral of applied voltage, so raising the voltage from zero over a second or two keeps the flux excursion inside the saturation limit, and the magnetizing peak stays near rated current instead of 15 times it. What the ramp cannot do is borrow the motor rating. A soft starter is designed around locked-rotor current at a poor power factor that falls as the rotor accelerates and back-EMF builds; a transformer presents magnetizing current at a very low power factor with no speed to help, for seconds at a time, over and over. So the model's documentation must name transformer or non-motor duty for this to be a legitimate choice, and the manufacturer's application note for the exact model is the only authority on that.

Size the unit at or above 36.1 A continuous in your enclosure and check the duty cycle of repeated energizations against its SCR heating limits. Check the bypass: an internal contactor that shorts the SCRs at full voltage is what keeps the unit cool in steady running; without it the power semiconductors carry the transformer continuously. On a motor you would set the current limit from locked-rotor current and the allowed start time, the conversion walked through in converting a 350 kVA soft start limit to starting current; a transformer has no equivalent knob, which is another reason the documentation governs. Decision: quote the soft starter when the paperwork supports transformer duty and the ETU path costs more than it is worth; otherwise it is not in the running.

Resistor pre-insertion: when the dip is the problem #

Pre-insertion puts resistance in series with the primary for the first cycles and shorts it out with a bypass device once the flux transient is over. It is the only one of the four options that reduces the current the supply actually delivers, so it is the one that fixes dips: if lights blink and drives drop out when the transformer closes, the trip settings are a side issue. Estimate the dip across the source impedance the way motor starting voltage dip calculation on an 11 kV bus works it, scaled to a 400 V supply, and let that number decide whether you need this at all.

The engineering is real and none of it is optional: the joule integral the resistor absorbs per energization, the sequencing of the bypass switch, the failure mode when the bypass does not close, since a stuck resistor leaves the load running under-voltage and needs its own protection, and the phase arrangement. A time delay of a couple of seconds is a control detail, not a design. Decision at 25 kVA: an engineered, quoted option for a supply that genuinely cannot take the transient, not a first move.

Proving the fix on site #

De-energize the supply, lock it out and prove absence of voltage before opening any panel or touching a termination; the secondary terminals are live at full voltage whenever the primary is energized, load or no load. With that done:

  • Before the change, note which protective element operated. Many trip units indicate the function that caused the last trip; read the breaker's own indication rather than guessing from timing alone.
  • Capture one energization on all three primary phases with a recorder that catches waveform peaks, a power-quality analyzer or storage-oscilloscope-class instrument with a clamp rated above 600 A, with the supply voltage dip on the same time base. A steady-state clamp reading tells you nothing about a 0.1 s transient.
  • After the change, energize several times over some minutes with the secondary unloaded, so residual flux and closing angle vary; require no trip, a dip the other loads tolerate, and a recorded peak below the pickup you set.
  • Prove protection still works: run the manufacturer's trip-test or secondary-injection procedure for the breaker, and file the captures with the coordination record.

Questions asked

Does the electronic trip unit limit the inrush current, or just stop the breaker tripping on it?

It only stops the tripping. The trip unit decides when the breaker opens; with the instantaneous pickup at 630 A it rides the transient while the full worst-case inrush still flows into the transformer and out of the supply. Current-limiting on a breaker datasheet means let-through energy while clearing a fault, which requires opening. When the current itself must be cut, such as a dip that drops other loads, that is soft-starter or resistor territory.

Is the 10 to 15 times rated current inrush figure guaranteed for my transformer?

No, it is the documented envelope for the transient, not a property of one unit. Core material, residual flux and the point on the voltage wave where the contacts close set each peak, which is why the same transformer trips protection on some starts and not others. Measure one energization with a peak-capturing recorder on all three phases and set the pickup above what you see, with the calculated worst case as the floor.

Can I just fit a larger fixed-trip breaker?

A higher ampere rating buys ride-through by giving up overload protection, and the code caps it: NFPA 70, 2023 edition, Table 450.3(B) limits a primary-only breaker to 125 percent of rated primary current, which is 50 A here, with the next standard size permitted. A type D curve or an aM fuse raises the instantaneous band to 10 to 20 times rating without touching the ampere rating, so overload protection survives, but the fixed band straddles the worst-case peak.

Does leaving the secondary load disconnected reduce the inrush?

Barely. Inrush is magnetizing current; it appears with the secondary open and is set by the applied voltage and the core's flux history, not by connected load. Energizing unloaded is still the correct test condition, because it separates the transformer's transient from any load inrush and keeps the measurement clean.

How many test energizations prove the new settings?

Several, spread over some minutes so residual flux and closing angle differ each time; one clean start proves little, since the worst case needs the contacts closing near a voltage zero with residual flux aligned with it. Record the current peak and the supply dip each time and keep the captures with the coordination record.

Keep reading

  • Explainer

    Converting a 350 kVA soft start limit to starting current

    A 350 kVA soft start limit is about 421 A of line current at 480 V: divide 350,000 VA by √3 × 480 V. The figure is apparent power, so no power factor enters the conversion, and it carries no duration — that comes from the torque-speed margin. The 12.5 kV fuse is a coordination problem; motor protection belongs at 480 V.

    Motors and motor starters

  • How-to

    Estimating transformer inrush current for protection coordination

    The rules of thumb are screening gates, not coordination inputs: reported inrush runs 8 to 30 times full-load current and lasts 10 cycles to a minute. Plot the decay curve Ipu = 6 × t^-0.31 with t in seconds — it passes through 25× at the first peak, 12× five cycles in and 3× at 10 s — keep the protective device curve above it and below the transformer damage curve, and handle cold-load pickup separately.

    Protection: breakers, fuses and SCCR

  • How-to

    Closed delta transformer fault current calculation

    Compute each delta branch from its own kVA and impedance, then take phasor differences at the line terminals: for a 150 kVA leg with two 100 kVA legs at 240 V and 3.3% Z each, the bolted three-phase terminal fault is highest at each end of the 150 kVA winding and lower at the junction of the two 100 kVA windings. Size secondary equipment on the higher terminal value.

    Protection: breakers, fuses and SCCR