Current IntelPower LibraryShop main store

Explainer

Converting a 350 kVA soft start limit to starting current

Motors and motor starters Published 8 min read

Short answer

A 350 kVA soft start limit is about 421 A of line current at 480 V: divide 350,000 VA by √3 × 480 V. The figure is apparent power, so no power factor enters the conversion, and it carries no duration — that comes from the torque-speed margin. The 12.5 kV fuse is a coordination problem; motor protection belongs at 480 V.

On this page
  1. What line current does the limit allow?
  2. Is a starting limit in kVA the same as one in kVAR?
  3. Where is the limit measured?
  4. How long does the starting current last?
  5. Is a 300 kVA transformer big enough for a 250 HP soft start?
  6. Can the primary fuse protect the motor?
  7. Why did the 10 A feeder fuse blow before the 20 A transformer fuse?
  8. Which starting method meets the limit?
  9. What should the plan be for this installation?
  10. Questions asked

A 350 kVA soft start limit at 480 V is about 421 A of line current: I = S ÷ (√3 × V) = 350,000 VA ÷ (1.732 × 480 V) ≈ 421 A. The figure is apparent power, not kVAR, so no power factor enters the conversion. It carries no time either: how long the current lasts depends on the torque margin between motor and pump, not on the kVA number. And the fuse question aims at the wrong side — a medium-voltage primary fuse coordinates the utility system, while the motor's own protection belongs at the 480 V starter. Each answer below carries its arithmetic, using the 300 kVA transformer and the blown 10 A feeder fuse of this installation as the working case.

What line current does the limit allow? #

About 421 A per phase, assuming the limit is balanced three-phase apparent power measured at the motor terminals.

The three-phase conversion is current in amps = (kVA × 1,000) ÷ (√3 × line-to-line volts), with √3 ≈ 1.732; the single-phase form drops the √3 and uses the single voltage.

That is a conversion of a stated limit, not a starter setting. The current the motor actually draws is whatever the soft starter's current limit allows, and current limits are typically set between 250% and 350% of the motor's full-load current. The practical move is to set the starter's limit at or below that converted figure and log one start to see what it held. Treat the result as a calculated estimate to check against the starter's manual, the motor nameplate and the utility's wording of the restriction.

Is a starting limit in kVA the same as one in kVAR? #

No — kVA is apparent power and kVAR is only its reactive part, and the conversion to amps needs voltage alone, so no power factor is involved anywhere in it.

Apparent power is what the transformer, the cables and the utility restriction all see; real power in kW is what does work, and kVAR is the magnetizing piece that dominates a start. Power factor enters only when converting between those quantities — turning kW into kVA, or splitting kVA into its real and reactive parts. Starting current is overwhelmingly reactive, which is why it is large while the shaft power is still small, but that does not change the arithmetic: the amps are the same whatever the power factor happens to be.

Where is the limit measured? #

Settle it first, because the same apparent power is only about 16.2 A on the transformer primary: I = 350,000 VA ÷ (1.732 × 12,500 V) ≈ 16.2 A.

Apparent power is essentially conserved across the transformer, minus its losses, so a kVA restriction means the same thing on both sides; only the current differs, by the turns ratio. What changes is the equipment you evaluate and meter. Utility restrictions are normally set where the utility meters, so get the restriction in writing and confirm the measurement point and its time basis: an instantaneous ceiling, a demand-interval limit and a per-start allowance are different constraints. Until the utility documents otherwise, design to the low-voltage figure, which reflects to the primary figure above.

How long does the starting current last? #

Not from the kVA figure: the duration comes from the net accelerating torque between motor and pump and the combined inertia, and on a centrifugal pump that truly accelerates it typically runs five to twenty seconds.

An induction motor's torque falls roughly with the square of the applied voltage over the relevant range, so the same current limit that protects the transformer also strips the motor of torque. If the pump's torque-versus-speed demand crosses the motor's reduced-voltage torque curve, acceleration stops and the current never comes down. Duration therefore needs both torque-speed curves plus the combined inertia — the job of a transient motor-starting study, which system-study software does routinely.

The case numbers show how tight this is. A 560 A ceiling, described as twice the motor's full-load current, implies a 280 A nameplate; 560 A at the secondary bus is √3 × 480 × 560 ÷ 1,000 ≈ 466 kVA, and a 600 A estimate works out to ≈ 499 kVA. Both are over the restriction, which caps everything at the converted ceiling.

Against that 280 A nameplate, the ceiling is 150% of full load — half the low end of the band where soft-starter current limits normally sit. Expect a long ramp, a thin torque margin, and a stall if the transformer sags on top of the restriction. Before opening the starter or any enclosure to read settings or connect a logging clamp meter, open the disconnect, lock it out and test for absence of voltage; the logged start itself is done energized only under your site's live-work procedures with the protective equipment NFPA 70E, 2024 edition, requires.

Is a 300 kVA transformer big enough for a 250 HP soft start? #

Not quite: the start sits 17% above the 300 kVA nameplate, and the screening rule of at least 1.5 times horsepower in kVA calls for 375 kVA, so expect a deep dip and a stall risk.

The common screening rules are 2.5 to 3 times horsepower in kVA for across-the-line starting (625 to 750 kVA here) and at least 1.5 times for a soft start (375 kVA here) — quick filters, not designs. The transformer's full-load current is 300,000 ÷ 831.4 ≈ 361 A on the secondary, so the start rides above full load for the whole ramp. Whether seconds of 17% over nameplate matter thermally is judged the way evaluating dry-type transformer hot spot temperature rise describes: against the unit's insulation system and overload data.

The voltage side is the sharper problem — the dip is what a motor starting voltage dip calculation on an 11 kV bus puts a number on, and the same method applies on this primary with the transformer's impedance. The failure chain is short: the dip deepens, torque falls with the square of voltage, the ramp time expires before the motor reaches speed, and many soft starters then complete the ramp to full voltage — at which point the current is whatever the sagging transformer allows, near locked-rotor, and the restriction is gone.

Can the primary fuse protect the motor? #

No: NFPA 70, the National Electrical Code, 2023 edition, covers motor circuits and controllers in Article 430 and transformer overcurrent protection in Article 450, and neither article turns a medium-voltage fuse into motor protection.

A primary fuse must ride through transformer inrush and carry the reflected starting current for the ramp duration; motor overload, by contrast, is a sustained current only modestly above full load, reflected to the primary as a difference far smaller than any medium-voltage fuse curve can resolve. There is no fuse-only solution on the primary for motor protection. Overload, jam, unbalance and short-circuit protection belong in the starter — the choices selecting overload and jam protection for a reversible motor walks through — sized from the motor nameplate. Confirm the requirements with the local authority having jurisdiction and the equipment documentation; editions and local amendments differ.

Why did the 10 A feeder fuse blow before the 20 A transformer fuse? #

Because they are miscoordinated, and the feeder fuse is undersized for this transformer on its own: the 300 kVA unit draws 13.9 A of full-load current on the primary, already 39% above the feeder fuse's rating.

Ten amps at that primary voltage is only about 216 kVA of capability — below the transformer's own nameplate — so ordinary load eats its margin before any start. During the start the primary carries the reflected starting current for the ramp seconds: past the 10 A fuse's minimum-melting curve, comfortably inside the 20 A fuse's carry region, exactly the pattern observed. The fix is a time-current coordination study — the series-device margins that selective coordination margin requirements explains — plotting transformer inrush, the start current and both fuse curves together, not a bigger fuse on a guess. The medium-voltage side usually belongs to the serving utility, so coordinate any change with them.

Which starting method meets the limit? #

A soft starter set to hold the converted ceiling or less meets the restriction only if the pump still accelerates; a drive meets it with room to spare; across-the-line starting does not meet it at all.

Method What it changes Fits the ceiling?
Soft starter, limit at or below the converted ceiling Voltage and current during the ramp; torque falls with the square of voltage Yes, when the torque-speed margin holds — verify with a logged start
Variable frequency drive Frequency and voltage together, so current follows torque demand Yes, with margin; budget for harmonics and the drive's supply needs
Pony motor Pre-spins the pump before the main contactor closes Possible; a mechanical and sequencing project
Across the line Nothing; full voltage and locked-rotor current No

The transformer size pushes toward the drive: it is the one option that accelerates the pump at part current without trading away torque the way reduced voltage does.

What should the plan be for this installation? #

Four decisions: hold the starter at the converted ceiling or below, treat the 300 kVA transformer as undersized, keep motor protection at 480 V, and fix the blown-fuse problem with a coordination study instead of a bigger fuse.

  • Set the soft starter's current limit to the converted ceiling or below, after confirming with the utility where the restriction is measured and on what time basis.
  • Plan around the transformer: 375 kVA is the screening minimum for a 250 HP soft start, and 625 to 750 kVA for across-the-line. Until it is replaced or supplemented, accept starts only with the dip and torque margin verified — or move the pump to a drive.
  • Leave overload, jam, unbalance and short-circuit protection at the starter per NFPA 70 Article 430, and let Article 450 plus the utility govern the primary.
  • Re-plot the time-current curves of the 10 A feeder fuse and the 20 A transformer fuse against inrush and the start current; the 10 A fuse cannot survive this service at all.

Questions asked

Does the very low power factor during a start change the amps?

No. The conversion needs voltage alone, so the amps stay the same whether the starting power factor is 0.2 or 0.4. Power factor only splits apparent power into its parts: as a hypothetical example, at 0.25 power factor the same 350 kVA is about 87.5 kW of real power and 339 kVAR of reactive power. You need power factor to convert kilowatts into kVA, never to convert kVA into amps.

Where should the soft starter's current limit actually be set?

At or below the current the kVA restriction allows — the 421 A figure above. Soft starter current limits normally sit between 250% and 350% of the motor's full-load current, so with a 280 A nameplate the ceiling is only 150% of full load, low in that band. Confirm the starter's adjustable range in its manual, then log one test start to prove it held the set value.

Can the 10 A feeder fuse simply be upsized?

Not on its own. The transformer draws 13.9 A at full load on the primary, so the feeder fuse is undersized before any start happens, and during a start the primary carries about 16.2 A for the whole ramp. The fix is to re-plot the time-current curves of both fuses against transformer inrush and the start current together, usually with the serving utility, because that fuse is on their system.

Does the transformer's impedance hold the starting current down?

It deepens the voltage dip during the start, and the lower voltage does pull the current down — but torque falls with the square of voltage, so you lose acceleration at the same time. A small transformer is not a soft-start device: the dip that reduces current is the same dip that stalls the pump and stresses the transformer.

How do I confirm the start stayed under the ceiling?

Log one start with a power quality meter or the soft starter's event record, capturing line current and terminal voltage from the start command to steady speed. Compare the plateau the starter actually held against the converted ceiling. If the current sits at the limit while the motor never reaches full speed, the pump is stalling and no fuse change will fix that.

Keep reading

  • How-to

    Motor starting voltage dip calculation on an 11 kV bus

    A starting medium-voltage motor dips the bus in proportion to its locked-rotor kVA against the source's short-circuit strength. Screen it as dip ≈ 100 × S_start/S_sc at the point of common coupling, then refine with ΔV = I_start(R cosφ + X sinφ) per phase. In the worked 11 kV, 1.5 MVA chiller example a direct-on-line start gives 3.6% at the PCC and 4.0% at the plant bus, failing a 3% limit; a 65% tap autotransformer or a soft starter limited to 3× rated current holds both points under 2%.

    Motors and motor starters

  • Selection guide

    Selecting overload and jam protection for a reversible motor

    Set a bimetallic or electronic overload relay from the motor's nameplate full-load current — never from wattage — and give the electronic-clutch trip to a separate current-sensing jam or shock relay set above the highest normal process current. Its adjustable reset delay must outlast the cycle timer's worst-case command drop-out, and auto reset needs a deliberate-restart decision because a live run command restarts the motor.

    Motors and motor starters

  • Explainer

    Motor starter vs contactor: using a starter as one

    A motor starter is a contactor with an overload relay added: the relay's normally closed contact opens the coil circuit on sustained overcurrent. A starter works wherever a contactor is called for, provided three checks pass — horsepower rating at the supply voltage, coil voltage, and the overload setting against the motor's nameplate full-load current. A NEMA Size 1 covers a 3 HP motor.

    Motors and motor starters